Skip to main content

Notes for High Temperature Dust Collector Bags

 The high-temperature dust collector bag is formed by padding, pre-baking, and baking treatments of needle-punched nylon with hydrophobizing agent and oleophobic agent. After the hydrophobizing agent and oleophobic agent are quickly dried, they are attached to the surface of the filter material fiber in a net shape, thereby reducing the surface tension of water and oil and the filter bag, so that the wet filter medium formed by water, oil and dust will not adhere to the surface of the filter bag, thus avoiding the bag sticking phenomenon.

 

During the operation of the bag filter, the high-temperature dust collector bags contain more moisture and oily, hygroscopic and deliquescent dust in the gas, and it may generate water or oil film on the surface of the dust to increase adhesion, which can help capture dust, but will make cleaning difficult. Especially when the high temperature gas is in a high humidity state, condensation will occur due to the cooling effect of the outside air. This can not only cause the collected dust to scale or even block the surface of the filter bag, but also corrode structural materials, increase the resistance of the dust collector, and directly affect the normal operation of the bag filter. Ordinary filter media must be further improved in function to be suitable for this special working condition, prevent or reduce the phenomenon of dust bagging, and improve the service life and work efficiency of the filter media.

 

The fabric and design of the high-temperature dust collector bags should strive for high-efficiency filtration, easy dust stripping and durability. The selection of the dust bag is very important, it directly affects the dust removal effect of the dust collector. Choose the dust bag from the following aspects: gas temperature, humidity and chemistry, particle size, dust concentration, filter wind speed, cleaning dust mode and other factors. In the pulse and air box pulse dust collector, the dust is attached to the outer surface of the filter bag. When the dust-containing gas passes through the dust collector, the dust is trapped on the outer surface of the filter bag, and the clean gas enters the filter bag through the filter material. The cage inside the filter bag is used to support the filter bag to prevent the filter bag from collapsing, and at the same time it helps to remove and redistribute the dust cake.

 

Hebei Ou Tai Environmental Protection Equipment Co., Ltd. is a professional dust collector manufacturer. We provide ash valve, tops elevator buckets, ventilation butterfly valve, pulse jet type bag filter, electromagnetic pulse valve, bag supporting cages, high temperature fiberglass filter bag, polyester needle felt filter bags, Baghouse Filter, Electrostatic Dust Collector and so on. Want to know more? Please contact us.

 


Labels:

Comments

Post a Comment

Popular posts from this blog

The Electromagnetic Valve 2019

Electromagnetic pulse valves (also known as diaphragm valves) are compressed air "switches" for pulse bag filter dust cleaning systems. By the control of the output signal of the pulse jet control instrument, the filter bag is cleaned by one row (chamber), so that the resistance of the filter is kept within the set range, so as to ensure the processing capacity and dust collection efficiency of the filter. DMF-Z electromagnetic pulse valve  is a right-angle valve, and the angle between the inlet and outlet is 90 degrees, which is suitable for the installation connection between the airbag and the dust blower tube. The air flow is unobstructed and it can provide the required clear air pulse. DMF-ZM electromagnetic pulse valve is the same as the "Z" series of the right-angle valve, suitable for airbag and dust collector spray pipe installation connection, the import and export of the two ends with a fixed nut for installation so that installation and us
Post a Comment
Read more

Electrostatic Dust Precipitator

  1. Introduction of electrostatic dust precipitators   The power supply of the electrostatic precipitator consists of a control box, a step-up transformer and a rectifier. The output voltage of the power supply also has a great influence on the dust removal efficiency. Therefore, the operating voltage of the electrostatic precipitator must be maintained at 40-75kV or even above 100kV.   2. Basic structure of electrostatic dust precipitators   The electrostatic dust precipitators  are composed of two parts: one part is the main system of the electrostatic precipitator; the other part is the power supply device that provides high-voltage direct current and the low-voltage automatic control system. The high-voltage power supply system supplies power to the step-up transformer, and the dust collector of the dust collector is grounded. The low voltage electric control system is used to control the temperature of the electromagnetic vibrating hammer, the ash discharging electrode, the ash c
Post a Comment
Read more

Ash Discharge Valve

The opening and closing part of the ash discharge valve  electric plug valve is a gate plate, and the direction of movement of the gate plate is perpendicular to the direction of the fluid. The electric plug valve can only be fully opened and fully closed and cannot be adjusted or throttled. The gate has two sealing surfaces. The two sealing surfaces of the most commonly used mode gate valves form a wedge, and the wedge angle varies with the valve parameters. Principle: There is a round opening of a diameter on the gate, and the opening and closing of the gate makes the round opening on the gate to completely separate from and match with the diameter. Electric three-way valves are used for air conditioning, thermal ventilation, heat treatment in heat treatment plants, and industrial fluid control. Air-conditioning, heating, ventilation, domestic hot water and other civil systems and chemical, petroleum and metallurgical and fluid automation. Our dust collection syste
Post a Comment
Read more