Skip to main content

Scraper Conveyor

 With a squeegee chain traction, the conveyor that transports the bulk material in the tank is called a scraper conveyor. KS Scraper Conveyor Scraper Conveyor The adjacent middle slot can be flexibly limited in the horizontal and vertical planes. The face conveyor where the fuselage is bent at a 90-degree angle at the intersection of the work surface 1 and the transportation lane is called a "corner scraper conveyor".

 

In the current coal mining face, the role of scraper conveyor is not only to transport coal and materials, but also the operating track of the coal mining machine, so it has become an indispensable main equipment in modern coal mining technology. The scraper conveyor can keep running continuously and production can be performed normally. Otherwise, the entire coal mining face will show a state of discontinued production and disrupt the entire production.

 

The main structure and components of various types of scraper conveyors are basically the same, it consists of three parts: nose, middle and tail. In addition, there are auxiliary components such as a hydraulic jack device for moving the conveyor and a chain tensioner for tightening the chain. The head of the machine is composed of the headstock, electric motor, fluid coupling, reducer and sprocket. The middle part consists of transition slots, middle slots, chains, and scrapers. The tail is the device for the scraper chain return. Like the nose, the tail end of the heavy-duty scraper conveyor is also provided with a power transmission device to distinguish the upper head from the lower head from the installed position.

 

Scraper conveyor classification:

According to the arrangement and structure of the chute conveyor chute, it can be divided into two types: parallel chain and overlapping type. According to the number of chain and arrangement, it can be divided into single chain, double chain, double center chain and three chains.

 

working principle of Scraper Conveyor:

The working principle of the scraper conveyor is that the open chute is used as a bearing member for coal, vermiculite, or materials, and the scraper is fixed on the chain (composed of a scraper chain) as a traction member. When the head drive section is started, the sprocket on the motive head shaft rotates, causing the scraper chain to cycle and move the animal material along the chute until the head of the machine is unloaded. The scraper chain bypasses the sprocket for strapless, closed-loop operation to complete the material transfer.

 

Scraper conveyor advantages:

A solid structure. Can withstand the impact of coal, vermiculite or other materials, impact, collision, pressure, pressure and other external forces.

It can adapt to the need of the coal mining working face to be uneven and curved and can withstand vertical or horizontal bending.

Short body, easy to install.

Can double as the orbit of the shearer.

Can run in reverse, easy to handle the bottom chain accident.

Can be used as the fulcrum of the front section of the hydraulic support.

The structure is simple, in the length of the conveyor can be fed or unloaded at any point.

The enclosure is closed, which can prevent dust from flying and contaminate the environment when materials are transported.

When the tail does not set the shell, and insert the scraper into the stack, you can take the material delivery.

 

Scraper Conveyor Disadvantages:

No-load power consumption is high, about 30% of total power.

Not a long-distance transmission.

Easy to fall off the chain, jump chain accidents.

Consume more steel. The cost is high.

 

We are one of the best scraper conveyor suppliers,as a dust collection system manufacturer,we will give you the best service.

 


Comments

Popular posts from this blog

Electrostatic Dust Collector

The working principle of the electrostatic dust collector  is to use the high voltage electric field to ionize the flue gas. The dust charge in the air flow is separated from the air flow under the action of the electric field. The negative electrode is made of metal wires with different cross-sectional shapes and is called a discharge electrode. The positive electrode is made of metal plates of different geometries and is called a collecting electrode. The performance of an electrostatic precipitator is affected by three factors, the nature of the dust, the configuration of the equipment, and the flow rate of the flue gas. The specific resistance of dust is an index for evaluating conductivity, and it has a direct effect on the dust removal efficiency. The specific resistance is too low, dust particles are difficult to maintain on the dust collecting electrode, causing it to return to the air flow. The specific resistance is too high, and the dust particles that reach the dus...

The Electromagnetic Valve 2019

Electromagnetic pulse valves (also known as diaphragm valves) are compressed air "switches" for pulse bag filter dust cleaning systems. By the control of the output signal of the pulse jet control instrument, the filter bag is cleaned by one row (chamber), so that the resistance of the filter is kept within the set range, so as to ensure the processing capacity and dust collection efficiency of the filter. DMF-Z electromagnetic pulse valve  is a right-angle valve, and the angle between the inlet and outlet is 90 degrees, which is suitable for the installation connection between the airbag and the dust blower tube. The air flow is unobstructed and it can provide the required clear air pulse. DMF-ZM electromagnetic pulse valve is the same as the "Z" series of the right-angle valve, suitable for airbag and dust collector spray pipe installation connection, the import and export of the two ends with a fixed nut for installation so that installation and us...

Selection Principle of Cyclone Type Dust Collector

  1. Selection principle of cyclone type dust collector   ① The amount of gas purged by the cyclone type dust collector should be consistent with the amount of dust-containing gas that needs to be treated. The diameter of the cyclone type dust collector should be as small as possible. If the required air volume is large, it is advisable to use several small diameter cyclones in parallel.      ② The inlet wind speed of the cyclone dust collector should be maintained at 18~23m/s. When it is too low, the dust removal efficiency will decrease: when it is too high, the resistance loss and power consumption will increase, and the dust removal efficiency will not increase significantly.      ③ The selected cyclone type dust collector  has small resistance loss, low power consumption, simple structure and easy maintenance.      ④ The smallest dust particles that can be captured by the cyclone type dust collector should be slightly smaller than the dust particle siz...