Skip to main content

Standard Single Layer Felt Filter Bags

 Ⅰ. Introduction of standard single-layer felt filter bag

 

Industrial polypropylene (PP) and polyester (PE) standard felt filter bags, single-sided slip surface to prevent fiber migration, gradient pore deep filter type, no internal support layer. Use nearly 30 kinds of fibers with different diameters, and use fiber mixing equipment to make filter bags.

 

Ⅱ. Features of standard single-layer felt filter bag

 

1. Stitching method: ultrasonic welding or thread suture.

 

2. Sealing ring: polypropylene and polyester SDS, STS, galvanized steel ring or stainless steel ring.

 

3. Sealing ring connection method: ultrasonic welding or thread stitching.

 

4. Accuracy range: 1, 3, 5, 10, 25, 50, 75, 100, 150, 200 microns.

 

5. Efficiency: relative accuracy, single filtration efficiency is 85%.

 

6. Surface treatment: Smooth surface treatment to prevent fiber and leachate from freeing.

 

7. Material grade: fully comply with FDA grade requirements, free of silicon and other types of pollutants.

 

8. The replacement pressure difference is 0.10MPa, and the replacement pressure difference is 0.18MPa.

 

9. Extensive chemical compatibility of single-layer felt filter bags.

 

3. Application of standard single-layer felt filter bag

 

Automotive coatings and paints; water purification and water treatment; pharmaceuticals; catering; fine chemicals; electronics, etc.

 

Hebei Ou Tai Environmental Protection Equipment Co., Ltd. is a professional dust collector manufacturer. We provide ash valve, tops elevator buckets, ventilation butterfly valve, pulse jet type bag filter, electromagnetic pulse valve, bag supporting cages, high temperature fiberglass filter bag, polyester needle felt filter bags,  Baghouse Filter, Electrostatic Dust Collector and so on. Want to know more? Please contact us.

 


Comments

Popular posts from this blog

Electrostatic Dust Collector

The working principle of the electrostatic dust collector  is to use the high voltage electric field to ionize the flue gas. The dust charge in the air flow is separated from the air flow under the action of the electric field. The negative electrode is made of metal wires with different cross-sectional shapes and is called a discharge electrode. The positive electrode is made of metal plates of different geometries and is called a collecting electrode. The performance of an electrostatic precipitator is affected by three factors, the nature of the dust, the configuration of the equipment, and the flow rate of the flue gas. The specific resistance of dust is an index for evaluating conductivity, and it has a direct effect on the dust removal efficiency. The specific resistance is too low, dust particles are difficult to maintain on the dust collecting electrode, causing it to return to the air flow. The specific resistance is too high, and the dust particles that reach the dus...

The Electromagnetic Valve 2019

Electromagnetic pulse valves (also known as diaphragm valves) are compressed air "switches" for pulse bag filter dust cleaning systems. By the control of the output signal of the pulse jet control instrument, the filter bag is cleaned by one row (chamber), so that the resistance of the filter is kept within the set range, so as to ensure the processing capacity and dust collection efficiency of the filter. DMF-Z electromagnetic pulse valve  is a right-angle valve, and the angle between the inlet and outlet is 90 degrees, which is suitable for the installation connection between the airbag and the dust blower tube. The air flow is unobstructed and it can provide the required clear air pulse. DMF-ZM electromagnetic pulse valve is the same as the "Z" series of the right-angle valve, suitable for airbag and dust collector spray pipe installation connection, the import and export of the two ends with a fixed nut for installation so that installation and us...

Selection Principle of Cyclone Type Dust Collector

  1. Selection principle of cyclone type dust collector   ① The amount of gas purged by the cyclone type dust collector should be consistent with the amount of dust-containing gas that needs to be treated. The diameter of the cyclone type dust collector should be as small as possible. If the required air volume is large, it is advisable to use several small diameter cyclones in parallel.      ② The inlet wind speed of the cyclone dust collector should be maintained at 18~23m/s. When it is too low, the dust removal efficiency will decrease: when it is too high, the resistance loss and power consumption will increase, and the dust removal efficiency will not increase significantly.      ③ The selected cyclone type dust collector  has small resistance loss, low power consumption, simple structure and easy maintenance.      ④ The smallest dust particles that can be captured by the cyclone type dust collector should be slightly smaller than the dust particle siz...